|
|
|
2006 CABO RICO 47 PILOT
$759,900
SOLD

*Click here to view the 2006 Cabo Rico 47 Pilot Photo Gallery
STANDARD SPECIFICATIONS/OPTIONS PH47#1
HULL & DECK EQUIPMENT & RIGGING
Standard:
- Non skid deck surfaces with contrasting color
- All stainless steel or non-corrosive hardware
- Lights in cockpit lockers
- Wichard padeyes in cockpit ( 2 )
- Windlass, 12VDC Muir HRC2500
- 54CCST Lewmar Ocean Series genoa sheet winches
- 44CCST Lewmar Ocean Series staysail sheet winch
- 44CCST Lewmar Ocean Series main sheet winch
- 44ST Lewmar Ocean Series main halyard/reefing winch
- 40CCST Lewmar Ocean Series genoa & staysail halyard winches
- Doyle mainsail with full battens and 2 reef points
- Doyle staysail with UV shield
- Doyle 120 Genoa with UV shield
- Internal prestretch XLS halyards
- ProFurl roller furling genoa system
- Main halyard & two single line reefs led aft
- Flag halyards, port & starboard
- Internal main boom topping lift
- Internal main boom reef lines with purchase ( 2 )
- Main boom outhaul with purchase
- Harken Main boom roller bearing traveler with tackle
- Lazy jacks on mainsail
- Harken running gear blocks/tackle/traveler
- Custom chain plates with welded “ pin boss “
- Oversize SST wire standing rigging
- Open-bodied chrome/bronze turnbuckles
- Double anodized, powder coated, one piece spar
- Tapered mast, heavy duty double spreader rig
- Storage pennants for intermediate backstays
- Solid boom vang
- Heavy duty pin gooseneck
- Masthead sailing/anchor lights
- International navigation lights
- Foredeck flood light
- Double railed bow and stern pulpits
- Teak/SS clad bow sprit platform with two sets of anchor rollers with holding brackets
- Double below deck chain locker with deck pipe
- Companionway sea hood
- Custom teak/ ½” plexiglass main companionway hatch with internal security latch
- Solid teak companionway hatch boards
- Storage rack for companionway boards
- 6 Opening hatches ( 2 on PH cabin top )
- All hatches fitted with teak framed screens
- 8 Opening ports
- All ports fitted with screens
- Front opening window in Pilot house
- Port and starboard windshield wipers with washers
- Port and starboard flush winch handle boxes w /line bins
- Emergency tiller with access port
- Cockpit locker, port side
- Lazarette locker with hatch
- Helmsman seat
- Molded-in port & starboard strike rails with SS rubrail
- Heavy teak cap rail
- Raised bulwark
- Heavy SS lifeline stanchions, bulwark side mount bases, thru-bolted & back-plated
- Port & starboard double lifeline gates with safety hooks
- Stern rail gate with safety hook
- Varnished exterior teak
- SS or teak cabin top handrails
- Manual bilge pump-cockpit mounted
- 4 Teak low profile dorade boxes with SS guards
- 4 SS Dorades( 2 on PH cabin top )
- Outboard motor bracket
- Stern rail seats
- Teak flagstaff with socket
- Removable keeper bulkheads in lazarette, sail locker & forward anchor chain locker
- 4 port & starboard deck scuppers with 1 1/2” valves
- 2 2” cockpit scuppers with bronze valves
- LPG lockers- vented port and starboard
- Custom Edson spacesaver pedestal steering system with offshore pull-pull conduit & 36” SS wheel
- SP6 Ritchie compass
- Pedestal guard & brake
- Custom teak inlaid cockpit table
- Hot & cold cockpit shower
- Deck fills with integral keys
- Flexible vent scoops ( 3 )
Optional: PH47#1
- Hull, second waterline stripe
- Hull, bottom painted
- Solid SS rub strip for cap rail
- CoreCell deck construction( in lieu of ½” Baltek balsa core )
- Electric 58CCST Lewmar Ocean Series genoa sheet winches
- Electric 44CCST Lewmar Ocean Series staysail sheet winch
- Electric 48STC Lewmar Ocean Series main sheet/halyard reefing winch
- 48CCST Lewmar winches, secondaries
- Doyle staysail w/ UV protection for roller furling
- Profurl staysail furling system
- LeisureFurl boom main furling system
- Doyle mainsail for LeisureFurl
- Doyle 135 Genoa ( vs. std 120 )with UV shield
- Spreader soft end caps
- Light, masthead strobe with std. tricolor
- Lights, spreader, port & starboard
- Four cast SS dorade cowls on teak bases
- “ No Strike “ lightning protection device
- Folding mast steps
- 2nd Genoa halyard
- Wiring, extra tube in mast
- Windex @ masthead
- SS Pilot house window frames
- Lexan storm shutters for Pilot house windows
- Extra strength stern rail seats with SS cup holders
- Swim ladder with teak treads and bulkhead mounts, port & starboard
- Jackpoints ( 3 ) for windlass remote ( cockpit, inside helm, bow )
- Extended bow rail with teak seat and SS cup holder
- Saltwater wash down pump, 12VDC, foredeck
- 32” Lifelines
- Safety line folding padeyes on deck, port & starboard
- White web-style jack lines
- Companionway Doors with screens and holder plus dropboards
- Custom Teak cockpit grate
- 2 Solar ventilators ( PH center hatch, fwd cabin hatch )
- Quick release pins for dorade guards
- Extra opening hatch ( middle PH cabin top )
- 3rd windshield wiper and washer on center PH window ( fixed )
- Outlet, 12VDC, waterproof, cockpit
- Recessed Bose cockpit speakers ( 2 )
- Edson bi-spoke 44” SS steering wheel
- 4 additional opening ports for aft stateroom/head
- Line stowage hooks in cockpit locker
- Pin lock on lazarette locker hatch
- Windlass, 2nd gypsy with rope/chain system
- Windlass, down switch in addition to std.
- Forespar NovaLift hoist with outboard sling
- Offshore Winslow 6 man life raft ( with tripod arch tube, double insulated floor, boarding platform, EPIRB and Ultima wrap )
- Lazarette storage support for life raft
- Bimini with elk hide chafe strip and window over helm station-black Sunbrella
- Bimini cover-black Sunbrella
- Bimini bars, f/folding
- Sunbrella covers: pedestal, winches, dorades, windlass, companionway, hatches and mast collar-toast
- Sunbrella covered cockpit and helm seat cushions-toast w/black piping
- Sunbrella custom lazarette lounge cover w/ headrests-toast w/black piping
- Sunbrella chain covers( 2 )
- Sunbrella Pilot House window covers
MECHANICAL/ PLUMBING/ELECTRICAL
Standard:
- Yanmar 75HP diesel engine with FWC
- 4 Heavy duty engine mounts, alarm system, temp, oil & amp gauges, tachometer & hour meter
- Edson single lever engine controls
- HD engine exhaust hose, exhaust thru transom with custom waterlock
- Push-pull engine shift and throttle control cables
- Lead and mylar insulated engine room
- Aqualift muffler
- Engine room light
- Yanmar sailboat transmission, by Hurth for free-wheeling prop
- Three bladed bronze prop
- Engine room 12VDC ventilation system
- 1 ¼” Aquamet 22 solid SS prop shaft
- External cutlass bearing
- External water cooled shaft log with 2” red brass shaft log tube & bronze dripless stuffing box, aquadrive coupling
- Bulkhead mounted filters
- Fuel/water separator with fuel shut off valve
- Sea water intake strainer with shut off valve
- Bilge high water alarm
- Bilge pump operation counter
- Fuel tank clean out tubes for contaminated fuel
- Engine fuel prime pump
- High temp hoses on fresh water plumbing with SS hose clamps
- Mixer valves on all sink/shower faucets
- Marelon thru hulls and seacocks w/wood plugs
- All hoses meet or exceed ABYC standards
- All hose connections are double SS hose clamped
- 6 gallon SS hot water heater, 110VAC and off engine heat exchanger
- Heavy duty manual bilge pump
- Electric bilge pump with float switch
- Electric high capacity emergency bilge pump
- Water and fuel tanks manufactured from vinylester resin, iso gelcoat & 1810 Promat
- Integral baffles in each tank with inspection ports
- Fuel and water tanks have “ Wema “ gauges
- Fuel tanks have dip sticks
- Fuel lines connected with aircraft “ Aeroquip “ fittings
- 2 Fiberglass holding tanks
- Holding tanks with manual pump out
- LPG system w/ 2 10lb. tanks, electric solenoid shut off w/leak sensors, manual shut off and pressure gauge
- Complete large scale plumbing diagrams provided
- 12VDC-110VAC electrical panel ( Paneltronics ) with circuit breakers, switch “ ON “ indicator lights, color coded “ tinned strand “ copper wiring, conduit runs and thru bulkhead chafe protection. All cables and terminal blocks labeled for cross reference to wiring diagrams.
- SSB counterpoise laid in hull
- Amp and Volt gauges
- Link 10 battery monitor
- 110VAC polarity indicator
- 3 HD 12VDC 105 amp “ Lifeline “ deep cycle house batteries
- HD shore power inlet with 50’ 30 amp shore power cable and overload protector
- Battery selector switches with interconnect
- Propane sniffer, Xintex w/dual sensors
- Each 12VDC and 110VAC receptacle and light is individually wired ( no spliced together electrical harness )
- 2000 watt inverter/charger
- Electrical butt and terminal connectors are shrink sealed to eliminate moisture
- Ground wires are installed in shroud chainplates to facilitate future installation of lightning ground
- 12VDC & 110VDC systems meet or exceed ABYC standards
- 100 amp Balmar alternator with MC612 regulator
- 12VDC refrigeration
- Complete large scale wiring diagrams provided
- Complete owner’s manual for all systems
Optional: PH47#1
- John Deere 4045DFM, M2, low rev 85HP diesel engine with FWC
- Custom engine bed, drip pan, HD engine mounts
- Reverso oil change system
- Additional Fuel/water separator with manifold
- Engine spares kit, major
- Spare oil filters, impellors
- Fuse kit
- Vetus 80 bow thruster w/battery&box
- 4th and 5th Lifeline AGM batteries with boxes
- Link 2000 battery monitor/inverter/charge control
- 32000 BTU multi-zone air conditioning system-Cruisair
- Waste macerator system
- MaxProp VP ( adjustable pitch)
- Pre-set for generator, including wiring, breaker, genset bed, and fuel system ( genset to be installed at a later date )
- Genset access door in aft stateroom
- Pre-set for water maker including seacock and preplumbing ( water maker to be installed at a later date )
- Pre-set for washer/dryer ( to be installed at a later date )
- Grilles over water intakes
- Lightning ground plates (2)
- Steering quadrant access door from aft stateroom
- Simrad knot log, depth sounder, wind speed ( including wind direction ) with repeaters @ inside helm
- Bow thruster controls @ both helms
- Simrad autopilot
- Simrad autopilot controls @ both helms
- Simrad Radar/GPS/Plotters @ both helms( 7” in cockpit, 10” @ inside helm )
- Simrad VHF’s @ both helms, with hand phones
- Ritchie compasses @ both helms
- Radar antenna mount, mast bracket and guard
- Hailer speaker mounted on mast under radome
- Mobri SSRS4 radar reflector, mast mounted
- TV antenna, UFO style
INTERIOR
Galley
Standard:
- Lower vacuum panel door on refrigerator/freezer( 7.6 cu. Ft. )
- Double polished SS sinks
- Hot and cold pressure water
- Manual fresh water pump w/ water filter
- Food storage cabinets & utility drawers
- Force 10 three burner stove
- Custom teak stove tray
- Standard 12VDC freezer and refridgerator
- Microwave oven
- 110VAC outlet with circuit interrupter
- 12VDC fan
- Overhead and adjustable lights
- Under stove storage locker
- Pots and pans storage
- SS galley stove safety rail
- 1 SS opening port with screen
- Trash storage
- 1 opening hatch with teak framed screen
- Corian countertops
- Corian and teak icebox lids
- Corian sink covers w/cutting board underside
- Custom teak cabinets for plates/bowls, etc.
- Companionway storage unit
- Solid teak and holly sole
- Solid teak bulkhead staving
Optional: PH47#1
- Corian stove cover/serving tray
- Pantry door storage forward of inside helm station
- Teak paper towel holder
- Teak spice racks ( 2 )
Forward Cabin
Standard:
- 5” Multi-density berth cushion on island berth
- 2 SS opening ports with screens
- 1 Opening hatch with teak framed screen
- Lockers above berth
- Cedar lined hanging locker
- Hanging locker with interior light
- Vanity with mirror
- 2 overhead dome lights
- 2 Cantaloupe reading lights
- 12VDC fan
- 110VDC outlet
- 6 clothes drawers
- Solid teak louvered door with privacy lock
- Solid teak and holly sole
- Solid teak hull ceilings
- Solid teak bulkhead staving
Optional: PH47#1
- Vanity seat and desk with lifting corian top ( delete 2nd hanging lkr. )
- Custom solid teak headboard
- Custom curved solid teak trim throughout
- Extra courtesy lighting switching
- Hypervent mattress liner
- Custom 6” Zeno mattress
- Custom fitted sheets, bedspread ( Sunbrella designer fabric ), mattress cover, loose pillows
Forward Head
Standard:
- Marine head with Y valve
- Stall shower with teak sauna type seat
- Hot/cold pressure water
- 2 SS opening ports with screens
- 1 Opening hatch ( in shower ) with teak framed screen
- Overhead dome lights
- Solid teak locker doors with louvers
- Solid teak shower grate
- Head interior privacy lock
- Medicine locker w/ mirror
- Ceramic tile floor
- Laminate bulkheads with solid teak trim
- 110VAC outlet
- 12VDC fan
Optional: PH47#1
- Stone flooring
- Towel, washcloth, soap holder
- Solid teak magazine rack
DEN
Standard:
The den area is amidship to starboard and and is a custom
design configuration
Options PH47#1:
- Small curved settee in Sunbrella designer furniture fabric and fitted with a lee cloth ( hidden attachments )
- Storage under settee
- Custom inlaid teak table with custom SS base ( Champagne holder on ring on ring swivel). Removable inlaid top
- Custom bar cabinetry with teak and beveled glass doors and courtesy interior lighting
- Custom bookcase and wine storage
- Bose stereo speakers( 2 )
- Luke SS fireplace with stone tile backing and security bracing
- Custom handholds
- 2 Cantalupe reading lights
- 2 opening SS ports with screens
- 2 opening hatches with teak framed screens
- Electric fans( 2 )
- 2nd Pantry forward of mast w/solid teak louvered door
- Mast locker w/ door mounted wiring bus
- Solid teak and holly sole
- Solid teak hull ceilings
- Solid teak bulkhead staving and trim
PILOT HOUSE HELM
Standard:
- Inside steering station with engine controls
- Opening center windshield
- 1 opening hatch with teak framed screen
- 1 dorade inlet with teak surround closure
- Edson 20” SS steering wheel
- Ritchie compass
- WS, DS, and KL ( owner’s selection )
- Helm seat
- Teak helm control console and chart table w/ storage
- Helm SS security rail
- Solid teak and holly sole
- Solid teak staving and trim
Optional: PH47#1
- Additional large opening hatch with teak framed screen
- Edson 20” SS/ teak rimmed steering wheel
- Crown helm chair on SS pedestal w/millennium hi/lo, swivel base with fore and aft adjustment in black Ultraleather
- Custom teak covered helm SS security rail
- Binocular and misc. teak storage bin
- Drink holder
PILOT HOUSE SALOON
Standard:
- Large settee which converts to berth
- Lift up settee to reveal workroom and storage
- 5” layered density foam cushion with Scotchguard fabrics
- Bolstered cushions
- Courtesy lighting
- Inlaid teak table on SS pedestal base
- 1 dorade inlet with teak surround closure
- Solid teak and holly sole
- Solid teak staving and trim
- Dome lighting
- 12VDC fans (2)
Optional: PH47#1
- Custom teak beams in overhead
- Custom teak handholds in overhead and @ companionway
- Crown 3 millennium pedestal base and swivel top for saloon table and Hi/lo upgrade to pedestal base
- Custom inlay on folding table ( underside )
- Hidden storage locker
- Lee cloth for PH settee
- PH settee in Sunbrella designer furniture fabric with anti-chafe guards & loose pillows
- Securable cushion for PH table when in lo position
- Flat screen TV ( 15” Sharp Aquos ) on permanent mount
- Custom teak cabinet to enclose Sony CD, DVD, stereo & MP3 players
- Bose speakers and supplemental amplifier
AFT STATEROOM
Standard:
- Enclosed cabin with lifting teak panel access and solid teak door w/louvers
- Double berth with 5” layered density cushion in choice of fabric
- Hanging locker with solid teak louvered door, cedar lining and
Inside 12VDC lighting
- Solid teak and holly sole
- Solid teak louvered door cabinets
- Wet locker with drain
- 1 opening SS port
- 12VDC electric fan
- 110VAC outlet
- Cantaloupe reading lamps ( 2 )
- Vanity sink with hot and cold pressure water, corian counter top and teak medicine locker
- Standard marine head with Y valve
- Shower with hot and cold pressure water
- Overhead dome lights
- Solid teak shower grate
- Solid teak privacy door with louvers and lock
- Solid teak staving
- Solid teak entry steps
- Teak storage lockers over and outboard of berth
Optional: PH47#1
- Hypervent liner under bedding
- Fitted sheets ,mattress cover, bedspreads, loose pillows
- 4 additional SS opening ports with screens ( 2{4x10}, 2{5x12} )
- Bulkhead exhaust vent and blower
- Custom solid teak vanity surround
- Custom hinged vanity mirror
- Courtesy light switch
- Towel/washcloth/soap holders
WORKSHOP
Standard:
- Power assisted access under PH settee
- Solid teak entry steps
- Access ½ door to engine compartment
- Solid teak and holly sole
- L shaped workshop counter
- Louvered solid teak storage cabinet doors above and below workshop counter
- Numerous additional storage compartments
- Vice on removable board
Optional: PH47#1
- SS top for work counter
- Hidden security locker
MISCELLANEOUS OPTIONS: PH 47#1
- Locking and hinged floor hatches throughout
- Rounded tops on teak cabinet doors throughout
- Mikasa stemware, plates, bowls, etc. custom fit to cabinets
- Liquor decanters custom fit to cabinets
- SS exterior grab rails
- Norseman fittings
COMMISSIONING
Standard:
- Commissioning to include USCG equipment
- Commissioning package to include 60 lb. CQR, galvanized anchor shackle, 250’ chain, 6 white 3- strand docking lines, 4 fenders, nylon fender whipsSafety package to include 7 life jackets, flares, 3 fire ex.
Optional: PH47#1
- 2nd Anchor- Bruce 60 lb.with 50’ 3/8 HT chain and 250’ of ¾ “ rope road
- Primary anchor ( 60 lb CQR )upgrade to 250’ 3/8” HT chain in lieu of std.)
- Four black fender covers- Taylor-Made Premium
- Name and Hailing Port in gold leaf appliqué
- Custom teak/SS boat hook with retainers
- Para-Tech sea anchor (95,000 lbs. max ) with rode, tackle, buoys, etc.
- Extra Bomar hatch strut adjusters
- 4 Brass padlocks( combination )
- Extra zincs for prop and bow thruster
Back to Top
|